Wonderful Winter Princess Tiara and Wand
The Wonderful Winter Princess Tiara and Wand crochet Halloween pattern is meant to give you some cute accessories for your little princess's costume this year. Each accessory uses the same snowflake pattern in its own way. You'll work up five snowflakes to make super easy homemade Halloween costume accessories alongside a really cute dress pattern. Make them your own with different colors if you're not a fan of the winter theme. However you work up these Halloween crochet patterns is sure to please the princess in your life.
Crochet HookJ/10 or 6 mm hook
Yarn Weight(4) Medium Weight/Worsted Weight and Aran (16-20 stitches to 4 inches)
Crochet Gauge1 snowflake = 5 (12.5 cm), stretched.
Finished SizeWand measures 15 (38 cm) long. Snowflake measures 5 (12.5 cm), stretched.
- RED HEART Super Saver: 1 skein each 311 White A, 505 Aruba Sea B, and 995 Ocean D
- RED HEART Boutique Sashay Mini: 1 ball 2936 Bubbles C
- Susan Bates Crochet Hook: 6mm [US J-10]
- Yarn needle
- White foam visor
- White foam wand with star
- White glue or fabric stiffener
- Hot glue gun
- Aluminum foil
Special Stitches Beg 3-dc Cl (beginning 3 double crochet cluster) = Ch 2, yarn over, insert hook in indicated stitch or space, yarn over and pull up loop, yarn over, draw through 2 loops on hook (2 loops remain on hook); yarn over, insert hook in same stitch or space, yarn over and pull up loop, yarn over, draw through 2 loops, yarn over, draw through all 3 loops on hook. Picot = Ch 7, slip st in 3rd ch from hook, ch 4. 3-dc Cl (3 double crochet cluster) = Yarn over, insert hook in indicated stitch or space, yarn over and pull up loop, yarn over, draw through 2 loops on hook (2 loops remain on hook); [yarn over, insert hook in same stitch or space, yarn over and pull up loop, yarn over, draw through 2 loops] 2 times, yarn over, draw through all 4 loops on hook. Notes 1. Take care not to twist chains when making picots and the cluster stitch that follows. 2. Points of star on wand are cut off before adhering snowflakes on each side. 3. Foam visor is trimmed to narrower width and worn upside down. 4. An adult should always operate the hot glue gun.
(Make 5: 1 with A and 4 with B) With D, ch 4; join with slip st in first ch to form a ring. Round 1: Ch 5 (counts as dc, ch 2), dc in ring, *ch 2, dc in ring; repeat from * 3 times, ch 2; join with slip st in 3rd ch of beginning ch6 dc and 6 ch-2 spaces. Round 2: (Slip st, beg 3-dc Cl) in first ch-2 space, *picot, 3-dc Cl in next ch-2 space; repeat from * 4 times, picot; join with slip st to ch of beg 3-dc Cl. Fasten off.
Weave in ends. Saturate snowflakes with white glue or fabric stiffener, stretch and block on sheet of aluminum foil. Allow to dry thoroughly before handling. Wand Cut off the points from the star, leaving a pentagon-shaped piece. With hot glue, adhere a B-colored snowflake to each side. Securing ends with glue, wrap D around wand handle. Tie a long piece of C under wand tip and trim ends as desired. Tiara Trim visor to half of its original width. Holding visor upside down, with hot glue, adhere an A-colored snowflake to the center and a B-colored snowflake on each side.
Read NextHarry Potter Wand Crochet Pattern